Holoseat

h1. Tone Ring Half Assembly

{{>toc}}

h2. Tools

* Holoseat Test Stand

* Magnetic Compass

* Soldering Iron with clean wide flat tip

* Heat proof matt

* Spacer TODO - get dimensions

h2. Materials

* Instant/super glue (prefer Loctite Super Glue Ultragel Control)

* (1) 18PTR-01: Snap Fit 18 Pole Tone Ring Base

* (1) 18PTR-02: Snap Fit 18 Pole Tone Ring Cover

* (18) 18PTR-03: N52 3/16" x 3/16" Neodymium Cylinder Magnets

* (1) 18PTR-04: M3 x 0.5 mm Thread Size, 3.8 mm Installed Length Heat-Set Inserts for Plastics

Note:  The final build requires (2) *HS-03: 18 Pole Tone Ring Halves*

h2. Safety Issues

* Use safety glasses when working with small, high powered magnets to avoid eye injury from flying magnets  

* Be sure to maintain physical control of magnets (those being placed and those already placed) to avoid flying magnets

h2. Product

HS-03: 18 Pole Tone Ring Half

h2. Procedure

h3. 1. Place Heat-Set Insert

# Place the *18PTR-01: Snap Fit 18 Pole Tone Ring Base* on heat proof mat with the spacer supporting the overhanging tab

*INSERT PIC*

# Place *18PTR-04: M3 x 0.5 mm Thread Size, 3.8 mm Installed Length Heat-Set Inserts for Plastics* face up into the the hole in the *Tone Ring Base*

*INSERT SCHEMATIC*

*INSERT PIC*

# Set Soldering Iron to 350 Celsius and wait for it to reach temperature

# Use the flat of the soldering iron tip to apply gentle pressure to the *heat-set insert* until it melts into the hole and sits flush.  Take care not to twist or shift the insert.

*INSERT VID*

h3. 2. Place Initial Magnet

# South pole (attracts red indicator) facing out)

# Glue in place

# Wait 15 min

h3. 3. Place Remaining Magnets

# Select another magnet and find its polarity by placing it along the outside edge so that it becomes attracted to the previous magnet

# Rotate the magnet from the previous step 180 degrees (so that the pole attracted to the previous magnet is facing out to create a pole pair) and place it in the next slot in the base

*INSERT PIC*

# Repeat the previous two steps until the tone ring is fully populated

*INSERT PIC*

# Align and place the *18PTR-02: Snap Fit Tone Ring Cover* over the *18PTR-01: Snap Fit 18 Pole Tone Ring Base*

# Press the parts firmly to secure the cover to the base

*INSERT PIC*

h3. 4. Verify Magnet Placement

Note: You will need (2) in progress *HS-03: 18 Pole Tone Ring Halves* for testing

# Set up the Holoseat Test Stand

## Ensure the calibrated sensor is attached to the sensor controller

## Ensure the power and USB connections are all configured according to the test stand operating instructions

## Join (2) in progress *HS-03: 18 Pole Tone Ring Halves* onto the tone ring adapter

*INSERT PIC*

# Run tone ring test(s)

*INSERT TEST VID*

*INSERT RESULTS PIC*

# Remove the tone ring halves from the tone ring adapter

h3. 5. Fix Cover to Base

# Apply super glue to the *Base* as shown below

*INSERT PIC*

# Place *18PTR-02: Snap Fit 18 Pole Tone Ring Cover* onto *Base*

# Press the *Top* firmly onto the base for 1 minute

# Wait 1 hour

h3. 6. Verify Fit

Note: You will need (2) in progress *HS-03: 18 Pole Tone Ring Halves* which going forward will be considered a complete set

# ...

h2. References

* "What Are Magnetic Poles and How to Identify Them":https://www.apexmagnets.com/news-how-tos/what-are-magnetic-poles-and-how-to-identify-them/

* "Reading a Compass":http://www.compassdude.com/compass-reading.php