Software Source Code

Version 3 (J. Simmons, 12/11/2016 10:06 am)

1 2 J. Simmons
h1. Project Software
2 1 J. Simmons
3 2 J. Simmons
{{>toc}}
4 1 J. Simmons
5 2 J. Simmons
h2. Introduction
6 1 J. Simmons
7 2 J. Simmons
The Holoseat project has three software elements.  The first software element is the firmware running on the Holoseat controller.  The second software element is the desktop configuration app.  And the third software element is the test rig software (composed of more firmware and test execution software).  This page covers each of these elements and the serial protocol between the Holoseat controller and the desktop configuration app.
8 1 J. Simmons
9 2 J. Simmons
h2. Controller Firmware
10 1 J. Simmons
11 3 J. Simmons
The Holoseat controller firmware can be found in the "SVN Repository":https://opendesignengine.net/projects/holoseat/repository/show/trunk/holoseat_firmware.  It runs on an "Adafruit Feather":https://www.adafruit.com/feather and relies on the "Bounce2":https://github.com/thomasfredericks/Bounce2 library for button "debouncing":https://www.arduino.cc/en/Tutorial/Debounce.  Its basic function is to detect pedal events from the sensor, use the timing of those events to determine the cadence (in RPM) and direction (forward or backward), and then send the walk command (generally by pressing the 'w' or 's' key) when the pedal speed is greater than the specified trigger cadence.
12 3 J. Simmons
13 3 J. Simmons
The default parameters for the firmware are stored in the @holoseat_constants.h@ file so they will be available at start up without the need for a connection to the desktop configuration app.  The desktop configuration app modifies the default values by updating the values of the corresponding constants in this file and then flashing updated firmware to the Holoseat controller.  The following parameters have default values in the constants file.
14 3 J. Simmons
15 3 J. Simmons
* Default Walk Forward Character - what key is sent to move the character forward in the game
16 3 J. Simmons
* Default Walk Backward Character - what key is sent to move the character backward in the game
17 3 J. Simmons
* Default Holoseat Enabled - is the Holoseat enabled by default?
18 3 J. Simmons
* Default Trigger Cadence - how fast does the user need to pedal (in RPM) to trigger walking?
19 3 J. Simmons
* Default Logging Enabled - is serial logging enabled by default?
20 3 J. Simmons
* Default Logging Interval - how long between messages in serial logging in deci-seconds (0.1 of a second)
21 1 J. Simmons
22 2 J. Simmons
h2. Desktop App
23 2 J. Simmons
24 2 J. Simmons
tbd
25 2 J. Simmons
26 2 J. Simmons
h2. Test Rig Software
27 2 J. Simmons
28 2 J. Simmons
tbd
29 2 J. Simmons
30 2 J. Simmons
h2. HoloSeat Serial Protocol
31 2 J. Simmons
32 2 J. Simmons
The HoloSeat firmware has a serial protocol, the Holoseat Serial Protocol (HSP), to enable the desktop control application to modify all key parameters and to determine the current configuration of the Holoseat.
33 2 J. Simmons
34 2 J. Simmons
h3. Protocol Commands
35 2 J. Simmons
36 2 J. Simmons
The HSP supports three commands.  Each command is made up of a single upper case character indicating the statement type.  One command, the (S)et statement, also takes an input string.
37 2 J. Simmons
38 2 J. Simmons
* @?@ - Ready(?) command; used to determine if the HoloSeat is ready to receive commands over the HSP (will reply with the (R)eady message followed by one standard state message if the HoloSeat is ready)
39 2 J. Simmons
* @S <config string>@ - (S)et command; used to send updated configuration to HoloSeat (HoloSeat will reply with @OK@ on success).  The config string has the following format:
40 2 J. Simmons
@<WFC>,<WBC>,<E>,<TC>,<L>,<LI>@ - example: @S w,s,0,60,0,20@
41 2 J. Simmons
** @<WFC>@ - Walk forward character (example: w)
42 2 J. Simmons
** @<WBC>@ - Walk backward character (example: s)
43 2 J. Simmons
** @<E>@ - Enabled? Must be a @0@ (disabled) or a @1@ (enabled) (example: 1)
44 2 J. Simmons
** @<TC>@ - Trigger cadence (example: 65)
45 2 J. Simmons
** @<L>@ - Logging enabled? Must be a @0@ (disabled) or a @1@ (enabled) (example: 1)
46 2 J. Simmons
** @<LI>@ - Logging interval in deci-seconds (example: 10)
47 2 J. Simmons
* @Q@ - (Q)uery command; used to request the HoloSeat send one standard state message (see *Protocol Messages* below)
48 2 J. Simmons
49 2 J. Simmons
h3. Protocol Messages
50 2 J. Simmons
51 2 J. Simmons
The HSP has two messages.  One is a single character message similar to the commands and one is the HSP standard state message which is sent after initialization, in reply to a (Q)uery command, and as the serial logging message.
52 2 J. Simmons
53 2 J. Simmons
* @R@ - (R)eady; sent by the HoloSeat to indicate it is ready for serial communication; sent in reply to the Ready(?) command and when serial port is attached in debug mode (to be added)
54 2 J. Simmons
* @<VER>,<WFC>(<DWFC>),<WBC>(<DWBC>),<E>(<DE>),<C>/<TC>(<DTC>),<L>(<DL>)/<LI>(<DLI>)@ - standard state message, see below for key; example: @1.2.3,w(w),s(s),1(1),70/65(75),1(0)/10(10)@
55 2 J. Simmons
** @<VER>@ - Firmware version string (example: 1.2.3)
56 2 J. Simmons
** @<WFC>@ - Walk forward character (example: w)
57 2 J. Simmons
** @<DWFC>@ - Default walk forward character (example: w)
58 2 J. Simmons
** @<WBC>@ - Walk backward character (example: s)
59 2 J. Simmons
** @<DWBC>@ - Default walk backward character (example: s)
60 2 J. Simmons
** @<E>@ - Enabled? Must be a @0@ (disabled) or a @1@ (enabled) (example: 1)
61 2 J. Simmons
** @<DE>@ - Default enabled state, same format as @<E>@ (example: 1)
62 2 J. Simmons
** @<C>@ - Current cadence rounded to whole number; positive value means direction is forward, negative value means direction is backward (example: 70)
63 2 J. Simmons
** @<TC>@ - Trigger cadence (example: 65)
64 2 J. Simmons
** @<DTC>@ - Default trigger cadence (example: 75)
65 2 J. Simmons
** @<L>@ - Logging enabled? Must be a @0@ (disabled) or a @1@ (enabled) (example: 1)
66 2 J. Simmons
** @<DL>@ - Default logging enabled,  same format as @<L>@ (example: 0)
67 2 J. Simmons
** @<LI>@ - Logging interval in deci-seconds (example: 10)
68 2 J. Simmons
** @<DLI>@ - Default logging interval in deci-seconds (example: 10)
69 2 J. Simmons
70 2 J. Simmons
h3. Protocol Usage
71 2 J. Simmons
72 2 J. Simmons
Always start a serial session by sending a Ready(?) command.  If a (R)eady message is not received, wait and try again until a timeout is reached or a (R)eady message is received.  Be sure to check the version string sent in the initial standard state message to ensure your app is compatible with the version of the HoloSeat firmware.  
73 2 J. Simmons
74 2 J. Simmons
After you have initialized your connection, you can then use the (Set) and (Q)uery commands as necessary to control and observe the HoloSeat's state.