Holoseat

h1. Sensor Assembly

{{>toc}}

h2. Tools

* Holoseat Test Stand with computer to operate it

* Soldering iron with stand

* Helping hands

* Exhaust fan

* Sensor assembly jig (3D printed tool - provide link)

* Flush snips

* Small scissors 

* Safety glasses

h2. Materials

* Instant/super glue (prefer Loctite Super Glue Ultragel Control)

* Solder

* Isopropyl alcohol

* Cotton balls

* (1) WSSM-01: TRRS Audio Connector PCB

* (1) WSSM-02: TLE4966L Infineon Technologies High Precsn Hall / Board Mount Hall Effect/Magnetic Sensor

* (1) WSSM-03: Sensor Housing Lower Half

* (1) WSSM-04: Sensor Housing Upper Half

* (1) WSSM-05: 3M 9472LE Tape 5/8" x 1" piece

h2. Safety Issues

* Care must be taken when using the soldering iron, the tip is very hot

* Always wear safety glasses while working with soldering irons

* Avoid breathing in the soldering fumes, use a vent or hood if needed to provide adequate ventilation

h2. Product

HS-04: Wheel Speed Sensor Module

*Insert Pic*

h2. Procedure

h3. 1. Place sensor on TRRS Audio Connector PCB

# Place *WSSM-02: TLE4966L Sensor* in jig with label facing “out” (toward window in jig)

# Slide *TLE4966L Sensor* into jig until its label aligns can be seen through the window in jig

# Bend *TLE4966L Sensor* leads down along jig

# Place *TLE4966L Sensor* pins through holes in *WSSM-01: TRRS Audio Connector PCB* with the jack facing up

# Align *TRRS Audio Connector PCB* with lip on jig

# Bend *TLE4966L Sensor* leads over to fix position of sensor relative *TRRS Audio Connector PCB*

# Remove *TLE4966L Sensor/TRRS Audio Connector PCB* sub-assembly from jig

{{youtube(UJ_s2-SHfPo)}}

h3. 2. Solder TLE4966L Sensor to TRRS Audio Connector PCB

# Place *TLE4966L Sensor/TRRS Audio Connector PCB* sub-assembly in helping hands 

!step2.1-sm.jpg!

# Solder all 4 *TLE4966L Sensor* leads to their pins on the *TRRS Audio Connector PCB*

# Trim back excess leads from *TLE4966L Sensor* 

!step2.3-sm.jpg!

h3. 3. Verify sensor

# Place *TLE4966L Sensor/TRRS Audio Connector PCB* sub-assembly in *WSSM-03: Sensor Housing Lower Half*

!step3.1-sm.jpg!

# Connect sensor cable from test stand to *Wheel Speed Sensor* sub-assembly

# Place *Wheel Speed Sensor* sub-assembly in sensor mount on test stand

step3.3-sm.jpg

# Run tests - see test stand for API calls/application used for these tests (there is a CLI tool to run these tests automatically)

## Verify direction

### it should report cw when wheel turns 20 rpm cw

### it should report ccw when wheel turns 20 rpm ccw

## Verify cadence (using average cadence)

### it should report 30 +/- 2 when wheel turns cw at 30 rpm

### it should report 50 +/- 2 when wheel turns cw at 50 rpm

### it should report 45 +/- 2 when wheel turns cw at 45 rpm  

### it should report 25 +/- 2 when wheel turns cw at 45 rpm

h3. 4. Finish assembly

# Take *Wheel Speed Sensor* sub-assembly off test stand

# Place *WSSM-04: Sensor Housing Upper Half* on top of *WSSM-03: Sensor Housing Lower Half*

!step4.2-sm.jpg!

# Press *Sensor Housing Upper Half* into *Sensor Housing Lower Half* until it clicks into place and sits flush on the *Sensor Housing Lower Half*

!step4.3-sm.jpg!

# Add *9472LE Tape*

## Clean the bottom of the *Wheel Speed Sensor Module* with isopropyl alcohol using a cotton ball

## Wait for the alcohol to dry

## Cut 5/8" long piece of *9472LE Tape*

## Apply *9472LE Tape* to the bottom of the *Wheel Speed Sensor Module*

!step4.4.4-sm.jpg!

## Press *Wheel Speed Sensor Module* firmly onto a flat surface for 60 seconds

## Trim excess tape off of *Wheel Speed Sensor Module*

!step4.4.6-sm.jpg!