History

« Previous - Version 7/24 (diff) - Next » - Current version
J. Simmons, 12/25/2017 11:41 pm

Assembly Instructions

Introduction

TBD

Test Stand Body Assembly

Tools - Test Stand Body

  • Mitre Saw (preferably powered)
  • Pencil
  • Carpentry square
  • Tape Measure
  • Screw Gun
  • 1/16" Drill bit (for TS-07: 1-1/4" Fine Thread Drywall Screws)
  • 1/8" Drill bit (for TSB-03: #9 x 2-1/2" Coarse Thread Drywall Screws)
  • Phillips screw driving bit
  • (2) 12" (or larger) Bar clamps

Materials - Test Stand Body

  • (2) TSB-01: Side Boards
  • (2) TSB-02: Top Boards
  • (6) TSB-03: #9 x 2-1/2" Coarse Thread Drywall Screws
  • (1) TSB-04: 36" Long 2x3 Board
  • (1) TS-06: Nema 17 Stepper Motor Mount
  • (4) TS-07: 1-1/4" Fine Thread Drywall Screws
  • TSB-05: Semi-gloss latex paint

Safety Issues - Test Stand Body

  • Always wear safety glasses when working with carpentry tools
  • Take care when using saws (especially power saws)

Product - Test Stand Body

(1) TS-01: Holoseat Test Stand Body

Procedure - Test Stand Body

  1. Produce Side and Top Boards
    1. Use a miter saw to cut (2) 12" long boards from TSB-04: 36" Long 2x3 Board to produce (2) TSB-01: Side Boards
      (also requires tape measure, carpentry square, and pencil)
    2. Use a miter saw to cut (2) 5" long boards from TSB-04: 36" Long 2x3 Board to produce (2) TSB-02: Top Boards
      (also requires tape measure, carpentry square, and pencil)
  2. Assemble the TS-01: Holoseat Test Stand Body
    1. Use the bar clamps to secure (1) TSB-01: Side Boards and (1) TSB-02: Top Boards in a butt joint flush with the edge of the side board and with their ends aligned
    2. Drill (2) 1/8" pilot holes through the face of the side board and into the edge of the top board
    3. Use (2) TSB-03: #9 x 2-1/2" Coarse Thread Drywall Screws to secure the side board to the top board
    4. Repeat the past 3 steps to attach the other TSB-02: Top Boards to the side board making sure the gap between the top boards is wide enough for the TS-06: Nema 17 Stepper Motor Mount
      INSERT PIC HERE
    5. Place the TS-06: Nema 17 Stepper Motor Mount against the face of the side board between the top boards
    6. Drill (4) 1/16" pilot holes into the face of the side board
    7. Use (4) TS-07: 1-1/4" Fine Thread Drywall Screws to attach the motor mount to the side board making sure its top is flush with the top face of the top boards
      INSERT PIC HERE
    8. Use the bar clamps to secure the other TSB-01: Side Boards to the opposite side of the (2) TSB-02: Top Boards
    9. Drill (2) 1/8" pilot holes through the face of the side board and into the edges of the top boards (1 hole in each top board)
    10. Use (2) TSB-03: #9 x 2-1/2" Coarse Thread Drywall Screws to secure the side board to the top boards

adafruit_products_steppertest.jpg (66.7 kB) J. Simmons, 12/28/2017 06:47 pm

Also available in: HTML TXT