Safety Procedures v1 0

Version 14 (Jeremy Wright, 09/23/2012 10:56 pm)

1 1 Jeremy Wright
h1. Safety Procedures v1.0
2 1 Jeremy Wright
3 3 Jeremy Wright
{{toc}}
4 3 Jeremy Wright
5 3 Jeremy Wright
h2. Introduction
6 3 Jeremy Wright
7 12 Jeremy Wright
This document includes procedures that are designed to ensure the safe operation of the Shepard Test Stand. Each safety procedure item is labeled with a prefix of "STSSP", which stands for "Shepard Test Stand Safety Procedure". This prefix is followed by the number of the main section (i.e. 1), which is then followed by the number of the specific item (i.e. x.1). This is done so that the procedures are easy to reference for training purposes or to point out a specific safety violation. 
8 5 Jeremy Wright
9 3 Jeremy Wright
h2. Safety Procedures
10 1 Jeremy Wright
11 6 Jeremy Wright
* STSSP 1 - In accordance with the "NAR Motor Testing Manual":http://www.google.com/url?q=http%3A%2F%2Fwww.nar.org%2FSandT%2Fdocs%2FST-MotorTestingManual.pdf&sa=D&sntz=1&usg=AFQjCNGChzshgcfbwEm1PXViLOW7vVft5g :
12 6 Jeremy Wright
** STSSP 1.1 - Follow NAR Safety Code where appropriate (see next section for details).
13 6 Jeremy Wright
** STSSP 1.2 - Handle all motors and igniters per manufacturer’s instructions, including operating procedures and safe storage with particular attention to temperature and humidity.
14 6 Jeremy Wright
** STSSP 1.3 - Should a motor under test fail catastrophically, do not approach the test stand until it is safe to do so (any debris has landed, the motor is done firing, etc).
15 6 Jeremy Wright
** STSSP 1.4 - Should the test stand be damaged during testing, do not use the test stand for further testing until it has been repaired.
16 1 Jeremy Wright
17 7 Jeremy Wright
* STSSP 2 - In accordance with the "NAR Model Rocket Safety Code":http://www.google.com/url?q=http%3A%2F%2Fwww.nar.org%2FNARmrsc.html&sa=D&sntz=1&usg=AFQjCNFkY3NeRakCivqyUzsVvszCllJzWg :
18 7 Jeremy Wright
** STSSP 2.1 - Use only certified and unmodified commercial rocket motors (such as those manufactured by "Estes Rockets":http://www.google.com/url?q=http%3A%2F%2Fwww.estesrockets.com%2F&sa=D&sntz=1&usg=AFQjCNEN5a-gUdSYj_8-318YX-ZVpZRm1A ).
19 7 Jeremy Wright
** STSSP 2.2 - Use only unmodified commercial Launch Controllers (such as the "Electron Beam Launch Controller":http://www.google.com/url?q=http%3A%2F%2Fwww.estesrockets.com%2Frockets%2Faccessories%2Flaunch-systems%2F302220-electron-beamr-launch-controller&sa=D&sntz=1&usg=AFQjCNGVESTmvPU2X9Za8q9vk93EGQfTAA ) per manufacturer’s instructions to ignite the motor under test.
20 7 Jeremy Wright
** STSSP 2.3 - In the event of a misfire, remove the safety pin from the the Launch Controller and wait 60 seconds from the final test attempt before approaching the test stand.
21 14 Jeremy Wright
** STSSP 2.4 - Ensure all participants and observers stay out of the Safety Radius and Cones of Exclusion (including while setting up a test) as shown on the diagram below whenever the igniter is connected to the Launch Controller.  See Figure 2.4.
22 7 Jeremy Wright
** STSSP 2.5 - Ensure all participants and observers are aware of any tests about to begin.
23 7 Jeremy Wright
** STSSP 2.6 - Always use a countdown before igniting a motor during a test.
24 9 Jeremy Wright
** STSSP 2.7 - Only test A through E sized motors, and use the appropriate adaptors for A through D motors (see "Operating Manual":https://opendesignengine.net/projects/shepard-ts/wiki/Operating_Manual_v1_0 for more details).
25 5 Jeremy Wright
26 13 Jeremy Wright
* STSSP 3 - Fire Prevention and Management :
27 9 Jeremy Wright
** STSSP 3.1 - Do not operate the test stand in areas where there are local burn bans or zoning regulations.  Consult local officials for information concerning such bans or regulations.
28 9 Jeremy Wright
** STSSP 3.2 - Ensure the the testing area is clear of any flammable debris and operation of the test stand does not present a risk of fire (such as dry grass or brush fires).
29 9 Jeremy Wright
** STSSP 3.3 - Ensure the test stand is oriented such that the motor points away from any pathways (such as sidewalks, parking lots, or roads).
30 9 Jeremy Wright
** STSSP 3.4 - Ensure there is a large bucket of water and an All-Purpose Fire Extinguisher at the test control station (that is, next to the computer and Launch Controller) so there is easy access in the event of a small fire.
31 9 Jeremy Wright
** STSSP 3.5 - In the event of a small fire, put out grass (or similar) fires with the bucket of water, and put out fires on the test stand with the fire extinguisher.
32 9 Jeremy Wright
** STSSP 3.6 - In the event a small fire becomes a large fire, call the local fire department and maintain a safe distance.
33 9 Jeremy Wright
** STSSP 3.7 - Always follow general fire safety procedures when handling a fire event.
34 9 Jeremy Wright
35 1 Jeremy Wright
36 7 Jeremy Wright
h2. Figures
37 7 Jeremy Wright
38 8 Jeremy Wright
*Figure 2.4*
39 7 Jeremy Wright
!Shepard_Safety_Zones_Diagram.png!
40 5 Jeremy Wright
41 5 Jeremy Wright
h2. Glossary
42 5 Jeremy Wright
43 5 Jeremy Wright
NAR - National Association of Rocketry
44 5 Jeremy Wright
STSSP - Shepard Test Stand Safety Procedure