Assembly Instructions
Version 5 (J. Simmons, 12/25/2017 11:22 pm)
| 1 | 1 | J. Simmons | h1. Assembly Instructions |
|---|---|---|---|
| 2 | 1 | J. Simmons | |
| 3 | 1 | J. Simmons | {{toc}} |
| 4 | 1 | J. Simmons | |
| 5 | 1 | J. Simmons | h2. Introduction |
| 6 | 1 | J. Simmons | |
| 7 | 1 | J. Simmons | TBD |
| 8 | 1 | J. Simmons | |
| 9 | 1 | J. Simmons | h2. Test Stand Body Assembly |
| 10 | 1 | J. Simmons | |
| 11 | 1 | J. Simmons | h3. Tools - Test Stand Body |
| 12 | 1 | J. Simmons | |
| 13 | 2 | J. Simmons | * Mitre Saw (preferably powered) |
| 14 | 5 | J. Simmons | * Pencil |
| 15 | 2 | J. Simmons | * Carpentry square |
| 16 | 2 | J. Simmons | * Tape Measure |
| 17 | 2 | J. Simmons | * Screw Gun |
| 18 | 3 | J. Simmons | * 1/16" Drill bit (for TS-07: 1-1/4" Fine Thread Drywall Screws) |
| 19 | 4 | J. Simmons | * 1/8" Drill bit (for TSB-03: @#9@ x 2-1/2" Coarse Thread Drywall Screws) |
| 20 | 2 | J. Simmons | * Phillips screw driving bit |
| 21 | 5 | J. Simmons | * (2) 12" (or larger) Bar clamps |
| 22 | 1 | J. Simmons | |
| 23 | 1 | J. Simmons | h3. Materials - Test Stand Body |
| 24 | 1 | J. Simmons | |
| 25 | 5 | J. Simmons | * (2) TSB-01: Side Boards |
| 26 | 5 | J. Simmons | * (2) TSB-02: Top Boards |
| 27 | 5 | J. Simmons | * (6) TSB-03: #9 x 2-1/2" Coarse Thread Drywall Screws |
| 28 | 5 | J. Simmons | * (1) TSB-04: 36" Long 2x3 Board |
| 29 | 5 | J. Simmons | * (1) TS-06: Nema 17 Stepper Motor Mount |
| 30 | 5 | J. Simmons | * (4) TS-07: 1-1/4" Fine Thread Drywall Screws |
| 31 | 5 | J. Simmons | * TSB-05: Semi-gloss latex paint |
| 32 | 1 | J. Simmons | |
| 33 | 1 | J. Simmons | h3. Safety Issues - Test Stand Body |
| 34 | 1 | J. Simmons | |
| 35 | 5 | J. Simmons | * Always wear safety glasses when working with carpentry tools |
| 36 | 5 | J. Simmons | * Take care when using saws (especially power saws) |
| 37 | 1 | J. Simmons | |
| 38 | 1 | J. Simmons | h3. Product - Test Stand Body |
| 39 | 1 | J. Simmons | |
| 40 | 5 | J. Simmons | (1) TS-01: Holoseat Test Stand Body |
| 41 | 1 | J. Simmons | |
| 42 | 1 | J. Simmons | h3. Procedure - Test Stand Body |
| 43 | 1 | J. Simmons | |
| 44 | 5 | J. Simmons | # Produce Side and Top Boards |
| 45 | 5 | J. Simmons | ## Use a miter saw to cut (2) 12" long boards from *TSB-04: 36" Long 2x3 Board* to produce (2) *TSB-01: Side Boards* |
| 46 | 5 | J. Simmons | (also requires tape measure, carpentry square, and pencil) |
| 47 | 5 | J. Simmons | ## Use a miter saw to cut (2) 5" long boards from *TSB-04: 36" Long 2x3 Board* to produce (2) *TSB-02: Top Boards* |
| 48 | 5 | J. Simmons | (also requires tape measure, carpentry square, and pencil) |
| 49 | 5 | J. Simmons | # ... |