Ground Sphere CubeSat Ground Station

h1. Test 1.1.2 Instructions

{{toc}}

h2. Test Hardware

* Transmitter for lab and field tests - http://www.ti.com/ww/en/RF-BoosterPack/index.shtml

* Ground Sphere test rig

* 915 MHz transmitter, see link above

* Computer (min system reqs:_______________)

h2. Test 1: Lab Test

Lab test using low power transmitter at 915 MHz to confirm signal reception and system gain (not an AX.25 signal, but close enough).  These instructions assume that the receiver is already assembled and most recent software is installed.  If not, accomplish the next 2 steps.

# Follow the instruction for "GroundSphere Kit assembly"

# Follow the instructions for Operations Manual - "Getting Started and Set up"

Test Date: _________________________________   Test Location: ___________________________________________

Record Test Conditions: _________________________________________________________________________

*Additional Tools Needed:*

Tape Measure

*Safety concerns:*

_________________________ 

*Outcome*

* Partial verification of technical requirement 1.1.2, 

* Confirmation of Ground Sphere performance in best case laboratory conditions

* Confirmation of Ground Sphere performance in simulated orbital conditions

*Instructions:*

# [ ] Turn on computer

# [ ] Tuen on the transmitter

# [ ] Plug the GroundSphere USB data connector into an open USB port

# [ ] Plug the GroundShpere power cord into a standard 120v power outlet

# [ ] Record the distance between transmitter and receiver: _______________ (in meters?)

# [ ] Launch the _____ software

# [ ] tune the transmitter to 915 MHz

# [ ] Set transmitter power to ____________ _NOTE: (This is a reasonably strong terrestrial signal, and is an unrealistically high power to expect from SkyCube)_

# [ ] Tune the ________ software to receive 915 MHz

# [ ] Observe and capture/record the transmitted signal received by GroundSphere

# [ ] Move the transmitter ___________ (4 meters?) from the GroundSphere antenna

# [ ] set the transmitter power level to _______________.  _NOTE: (at this power level, we are simulating the signal that we expect to receive form SkyCube as it flys directly overhead of the antenna, given its orbital parameters <link to TLE file used in calculations> )_

# [ ] Observe the transmitted signal received by GroundSphere

<insert image of laboratory setup> 

<insert screenshot image of computer screen showing high power 915 MHz signal> 

<insert screenshot image of computer screen showing low power 915 MHz signal>

*TEST PROCEDURE COMPLETE*

h2. Test 2: Field Test

Long range field test using low power transmitter at 915 MHz to simulate predicted link budget (which comes from <insert link to spreadsheet> analysis) and confirm signal reception.  It is recommended to conduct this test with at least 2 individuals.  These instructions assume that the receiver is already assembled and most recent software is installed.  If not, accomplish the next 2 steps.

# Follow the instruction for "GroundSphere Kit assembly"

# Follow the instructions for Operations Manual - "Getting Started and Set up"

Test Date: _________________________________   Test Location: ___________________________________________

Record Test Conditions: _________________________________________________________________________

*Additional Tools Needed:*

Portable table or truck bed (on which to set up receiver equip and computer)

Access to 120V a/c power for computer (generator or car inverter)

Access to separate 120V a/c power for transmitter (generator or car inverter)

Multiple outlet, or power strip

Tape measure or distance finding equipment (GPS?)

*Safety concerns:*

Weather caution

Traffic caution

Portable power for equipment(?)

*Outcome*

* Partial verification of technical requirement 1.1.2, 

* Confirmation of Ground Sphere performance in optimal fielded conditions

* Confirmation of Ground Sphere performance at a far distance to simulate orbital conditions

*Instructions:*

> Mission Control Set Up

# [ ] Set up receiver and computer on portable table.

# [ ] Turn on computer

# [ ] Plug the GroundSphere USB data connector into an open USB port

# [ ] Plug the GroundShpere power cord into a standard 120v power outlet

# [ ] Launch the _____ software

# [ ] Move to a distance ______ (km) away from the receiver set up, then set up the transmitter

# [ ] Record the distance between transmitter and receiver: _______________ (in km?)

> Remote transmit site Set Up

# [ ] Power on and tune the transmitter to 915 MHz

# [ ] Set transmitter power to ____________ _NOTE: (This is a reasonably strong terrestrial signal, and is an unrealistically high power to expect from SkyCube)_

# [ ] Tune the ________ software to receive 915 MHz

# [ ] Observe and capture/record the transmitted signal received by GroundSphere

# [ ] Set the transmitter power level to _______________.  _NOTE: (at this power level, we are simulating the signal that we expect to receive form SkyCube as it flys directly overhead of the antenna, given its orbital parameters <link to TLE file used in calculations> )_

<insert image of receiver setup> 

<insert image of transmitter setup> 

<insert screenshot image of computer screen showing high power 915 MHz signal> 

<insert screenshot image of computer screen showing low power 915 MHz signal>

*TEST PROCEDURE COMPLETE*

h2. Test 3: From Orbit Test

acquire signal from orbiting cubesat operating on 915 MHz (NPS just launched two cubesats which use the same radio and configuration as SkyCube).  Orbital prediction software will need to be used to calculate the appropriate timing for this test.  It is only possible to conduct the steps below in anticipation of a 915 MHz signal source flying overhead.  These instructions assume that the receiver is already assembled and most recent software is installed.  If not, accomplish the next 2 steps.

# Follow the instruction for "GroundSphere Kit assembly"

# Follow the instructions for Operations Manual - "Getting Started and Set up"

Test Date: _________________________________   Test Location: ___________________________________________

Record Test Conditions: _________________________________________________________________________

*Tools Needed:*

Ground Sphere test rig

915 MHz transmitter, see link above

Computer (min system reqs:_______________)

Tape Measure or distance find equipment (GPS?)

*Safety concerns:*

Weather caution

Traffic caution

* 

*Outcome*

*Instructions:*

<insert screenshot image of computer screen showing signal received from satellite>

*TEST PROCEDURE COMPLETE*