Wiki
Version 3 (Matt Maier, 08/16/2014 03:10 pm) → Version 4/8 (Matt Maier, 08/16/2014 03:20 pm)
[[statement of intent]]
[[assumptions]]
[[introduction]]
[[acquisition]]
[[construction]]
[[calibration]]
[[troubleshooting]]
Hokay, so. I'm going to start by collecting a bunch of the links I've been keeping track of.
In no particular order (at the moment)
* reprap.org (wiki)
** "calibration":http://reprap.org/wiki/Calibration
** "software tweaking manual":http://reprap.org/wiki/RepRapSoftwareTweakingManual
** "triffid hunter's calibration guide":http://reprap.org/wiki/Triffid_Hunter's_Calibration_Guide
** "print troubleshooting pictorial guide":http://reprap.org/wiki/Print_Troubleshooting_Pictorial_Guide
** "leveling the bed":http://reprap.org/wiki/Leveling_the_Print_Bed
* the3dprinter.blogspot.com
** "firmware calibration":http://the3dprinter.blogspot.com/2012/02/durbie-prusa-mendel-calibration.html
** "skeinforge settings":http://the3dprinter.blogspot.com/2012/03/skeinforge-setting.html
** "print calibration":http://the3dprinter.blogspot.com/2012/03/calibration-with-prints.html
** "filament tips":http://the3dprinter.blogspot.com/2012/02/pla-and-abs-filament.html
** "tools":http://the3dprinter.blogspot.com/2012/02/3d-printer-tools.html
** "troubleshooting":http://the3dprinter.blogspot.com/2012/03/troubleshooting.html
* fabmetheus.crsndoo.com
** "skeinforge manual":http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge
* thingiverse
** "calibrate parts to fit":http://www.thingiverse.com/thing:52946
** "calibrate for part fitting":http://www.thingiverse.com/thing:342198
** "bed leveling calibration":http://www.thingiverse.com/thing:13053
** "calibration set":http://www.thingiverse.com/thing:5573
** "print temperature calibration":http://www.thingiverse.com/thing:35088/#instructions
* "slic3r manual":http://manual.slic3r.org/
* building a 3d printer
** "extruder calibration":http://my3dprinterbuild.wordpress.com/2013/01/18/extruder-calibration/
* richrap.blogspot.com
** "slic3r is nicer part 1":http://richrap.blogspot.com/2012/01/slic3r-is-nicer-part-1-settings-and.html
** "slic3r is nicer part 2":http://richrap.blogspot.com/2012/01/slic3r-is-nicer-part-2-filament-and.html
** "slic3r is nicer part 3":http://richrap.blogspot.com/2012/01/slic3r-is-nicer-part-3-how-low-can-you.html
* solidoodletips
** "setting the flow rate":http://solidoodletips.wordpress.com/2012/08/16/setting-the-flow-rate/
* just print 3d
** "prelude to calibration":http://www.justprint3d.com/3d-printer-calibration-prelude-things-to-set-before-your-first-printcalibration/
** "calibration basic 1":http://www.justprint3d.com/3d-printer-calibration-basic-1-stepsmm-values/
** "calibration basic 2":http://www.justprint3d.com/3d-printer-calibration-basic-2-extrusion-widthlayer-height-value/
* ultimaker
** "troubleshooting":https://www.ultimaker.com/pages/support/faq/ultimaker-original-troubleshooting
** "visual ultimaker troubleshooting":http://support.3dverkstan.se/article/23-a-visual-ultimaker-troubleshooting-guide
* minow
** "calibrating a delta printer":http://minow.blogspot.co.at/index.html#4918805519571907051
* hydraraptor (nophead
** "hole size":http://hydraraptor.blogspot.com/2011/02/polyholes.html
* miscellaneous
** "diagram of print cross section":http://www.printrbottalk.com/forum/viewtopic.php?p=29541#p29541
** "calibrating reprap":https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
** "10 rules for top notch prints":http://3.dmake.me/blog/2014/10-rules-top-notch-prints-printrbot-simple/
[[assumptions]]
[[introduction]]
[[acquisition]]
[[construction]]
[[calibration]]
[[troubleshooting]]
Hokay, so. I'm going to start by collecting a bunch of the links I've been keeping track of.
In no particular order (at the moment)
* reprap.org (wiki)
** "calibration":http://reprap.org/wiki/Calibration
** "software tweaking manual":http://reprap.org/wiki/RepRapSoftwareTweakingManual
** "triffid hunter's calibration guide":http://reprap.org/wiki/Triffid_Hunter's_Calibration_Guide
** "print troubleshooting pictorial guide":http://reprap.org/wiki/Print_Troubleshooting_Pictorial_Guide
** "leveling the bed":http://reprap.org/wiki/Leveling_the_Print_Bed
* the3dprinter.blogspot.com
** "firmware calibration":http://the3dprinter.blogspot.com/2012/02/durbie-prusa-mendel-calibration.html
** "skeinforge settings":http://the3dprinter.blogspot.com/2012/03/skeinforge-setting.html
** "print calibration":http://the3dprinter.blogspot.com/2012/03/calibration-with-prints.html
** "filament tips":http://the3dprinter.blogspot.com/2012/02/pla-and-abs-filament.html
** "tools":http://the3dprinter.blogspot.com/2012/02/3d-printer-tools.html
** "troubleshooting":http://the3dprinter.blogspot.com/2012/03/troubleshooting.html
* fabmetheus.crsndoo.com
** "skeinforge manual":http://fabmetheus.crsndoo.com/wiki/index.php/Skeinforge
* thingiverse
** "calibrate parts to fit":http://www.thingiverse.com/thing:52946
** "calibrate for part fitting":http://www.thingiverse.com/thing:342198
** "bed leveling calibration":http://www.thingiverse.com/thing:13053
** "calibration set":http://www.thingiverse.com/thing:5573
** "print temperature calibration":http://www.thingiverse.com/thing:35088/#instructions
* "slic3r manual":http://manual.slic3r.org/
* building a 3d printer
** "extruder calibration":http://my3dprinterbuild.wordpress.com/2013/01/18/extruder-calibration/
* richrap.blogspot.com
** "slic3r is nicer part 1":http://richrap.blogspot.com/2012/01/slic3r-is-nicer-part-1-settings-and.html
** "slic3r is nicer part 2":http://richrap.blogspot.com/2012/01/slic3r-is-nicer-part-2-filament-and.html
** "slic3r is nicer part 3":http://richrap.blogspot.com/2012/01/slic3r-is-nicer-part-3-how-low-can-you.html
* solidoodletips
** "setting the flow rate":http://solidoodletips.wordpress.com/2012/08/16/setting-the-flow-rate/
* just print 3d
** "prelude to calibration":http://www.justprint3d.com/3d-printer-calibration-prelude-things-to-set-before-your-first-printcalibration/
** "calibration basic 1":http://www.justprint3d.com/3d-printer-calibration-basic-1-stepsmm-values/
** "calibration basic 2":http://www.justprint3d.com/3d-printer-calibration-basic-2-extrusion-widthlayer-height-value/
* ultimaker
** "troubleshooting":https://www.ultimaker.com/pages/support/faq/ultimaker-original-troubleshooting
** "visual ultimaker troubleshooting":http://support.3dverkstan.se/article/23-a-visual-ultimaker-troubleshooting-guide
* minow
** "calibrating a delta printer":http://minow.blogspot.co.at/index.html#4918805519571907051
* hydraraptor (nophead
** "hole size":http://hydraraptor.blogspot.com/2011/02/polyholes.html
* miscellaneous
** "diagram of print cross section":http://www.printrbottalk.com/forum/viewtopic.php?p=29541#p29541
** "calibrating reprap":https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
** "10 rules for top notch prints":http://3.dmake.me/blog/2014/10-rules-top-notch-prints-printrbot-simple/