h1. Procurement/Manufacture v1.0

h3. Mechanical System

All of the items in the mechanical system are described on the "wiki":https://opendesignengine.net/projects/shepard-ts/wiki/Detailed_Design_v1_0#Mechanical-System , and detailed information including measurements can be found in the "BoM (Bill of Material)":http://opendesignengine.net/dmsf_files/18?download= .

* The lumber used to build version 1.0 of the test stand was standard English unit stock, and could be purchased anywhere including "Lowes":http://www.lowes.com and "Home Depot":http://www.homedepot.com in the U.S.
* The coarse thread drywall screws used as fasteners were standard English unit stock, and could be purchased anywhere including "Lowes":http://www.lowes.com and "Home Depot":http://www.homedepot.com in the U.S.
* The drawer slide used as a linear guide is PN "D80614C-ZP-W":http://www.libertyhardware.com/search/detail/?searchType=retail&ID=D80614C-ZP-W&FIN=ZP from "Liberty Hardware":http://www.libertyhardware.com .
* Several COTS (Commercial Off The Shelf) items were purchased as part of an "engine mount kit":http://www.estesrockets.com/rockets/accessories/engine-mounting/303159-d-and-e-engine-mount-kit from "Estes Rockets":http://www.estesrockets.com/ :
** Estes E Engine Mount Tube (PN 30463)
** Estes E Engine Retainer Ring (PN 30160)
** Estes E Spacer Ring (PN 35005)
** Estes E Engine Block (PN 30174-S) - modified
** Estes E Engine Hook (PN 35022)

h3. Data Acquisition (DAQ) System

The items in the DAQ system are described on the "wiki":https://opendesignengine.net/projects/shepard-ts/wiki/Detailed_Design_v1_0#Data-Acquisition-DAQ-System .

* The "Arduino Uno":http://arduino.cc/en/Main/ArduinoBoardUno used in this project was purchased from "Radio Shack":http://www.radioshack.com/product/index.jsp?productId=12268262 , but can also be purchased from vendors like "SparkFun":https://www.sparkfun.com/products/11021 . It can also be purchased from the "Arduino Store":http://store.arduino.cc/ww/index.php?main_page=product_info&cPath=11_12&products_id=195 for around the same price if you are willing to wait 15 days shipping time. The Uno used in the version 1.0 test stand was purchased at Radio Shack.
* The "Arduino ProtoShield":http://arduino.cc/en/Main/ArduinoProtoShield used in the version 1.0 of the test stand was a true Arduino product, and was purchased at Radio Shack for about $20. Not all Radio Shacks will have the ProtoShield in stock though. The ProtoShield can be purchased from the "Arduino Store":http://store.arduino.cc/ww/index.php?main_page=product_info&cPath=11_5&products_id=203 for around $10 more than you'd pay from U.S. based vendors. Similar boards can be purchased from many vendors including "AdaFruit":https://www.adafruit.com/products/51 for $20 including shipping. 
* The "Force Sensing Resistor (FSR)":http://www.trossenrobotics.com/store/p/6496-1-5-Inch-Force-Sensing-Resistor-FSR-.aspx used in version 1.0 of the test stand was purchased from "Trossen Robotics":http://www.trossenrobotics.com
* The "Type K Thermocouple":http://adafruit.com/products/270 used in version 1.0 of the test stand was purchased from "Adafruit Industries":http://adafruit.com
* The "operational amplifier":http://www.mouser.com/ProductDetail/Texas-Instruments/TLV2374IN/?qs=st7IWvlL5/gZGpqMaJgalj%252bttKJ3M/YPFWapqS2bl%252bg%3D used to amplify the signal from the FSR in version 1.0 of the test stand was purchased from "Mouser Electronics":http://www.mouser.com .
* The two 560 Ohm resistors used in version 1.0 were also purchased from "Mouser Electronics":http://www.mouser.com so that shipping costs could be combined.
* The "thermocouple amplifier":http://adafruit.com/products/269 used in version 1.0 was purchased from "Adafruit":http://adafruit.com .
* The FSR cable was made from scrap CAT 5e cables that were on hand. The wires used in soldering the ProtoShield were "breadboard jumper wire":http://www.radioshack.com/product/index.jsp?productId=2103801 available at Radio Shack.