Issues

Filters

Apply Clear

Toggle_check # Project Tracker Status Priority Subject Assignee Updated
120 AttenuatorXBugNewNormalSomething in my design seems to cause failures on pin PC1 when the Brown-out detection is enabled on the AVR microcontroller.02/11/2013 08:29 pm
119 AttenuatorXBugNewHighNo strain relief was provided for the battery connection.02/11/2013 08:27 pm
118 AttenuatorXBugNewHighThe LEDs displaying attenuation level are in opposite order. MSB should be on the left, like the silkscreen, but it’s on the right.02/11/2013 08:27 pm
117 AttenuatorXBugNewNormalThe pad I designed for the on-off switch isn’t wide enough. With enough solder, it works, but it’s not right.02/11/2013 08:26 pm
115 AttenuatorXBugNewNormalThe header should be SMT (as I already determined in the BOM), not through-hole (as I designed the board), and it should be on the bottom of the board.02/11/2013 08:25 pm
232 CNC Mill: 4x8 Wood (<$500), Fresno IdeaworksMilestoneNewNormalBuild the X and Y axes11/02/2013 06:33 pm
231 CNC Mill: 4x8 Wood (<$500), Fresno IdeaworksMilestoneNewNormalBuild the Y axis11/02/2013 06:32 pm
230 CNC Mill: 4x8 Wood (<$500), Fresno IdeaworksMilestoneNewNormalDesign X and Y axes11/02/2013 06:31 pm
229 CNC Mill: 4x8 Wood (<$500), Fresno IdeaworksMilestoneNewNormalFlash an ATMEGA328 with grbl firmware11/02/2013 06:15 pm
228 CNC Mill: 4x8 Wood (<$500), Fresno IdeaworksMilestoneNewNormalDesign the base (table)11/02/2013 06:12 pm
227 CNC Mill: 4x8 Wood (<$500), Fresno IdeaworksMilestoneNewNormalBuild the base (table)11/02/2013 06:12 pm
226 CNC Mill: 4x8 Wood (<$500), Fresno IdeaworksMilestoneIn ProgressNormalAssemble Stepper Motor Driver BoardsSteve Popenoe11/02/2013 05:27 pm
52 Dante FurnaceSupportIn ProgressNormalSource02/18/2012 10:16 pm
69 Epoxy Granite CNC MillFeatureNewNormalMake MoldBrandin Watson07/13/2012 08:48 pm
68 Epoxy Granite CNC MillFeatureNewNormalFinish v1 design of millBrandin Watson07/13/2012 08:43 pm
67 Epoxy Granite CNC MillFeatureNewNormalVacuumTrenton Wilson07/13/2012 08:40 pm
70 Epoxy Granite CNC MillMilestoneNewNormalPour BaseBrandin Watson07/13/2012 08:51 pm
65 Far Horizons ProjectMilestoneIn ProgressNormalAdler Planetarium Documentation Visit06/26/2012 06:59 pm
146 Groundstation v.2.0MilestoneNewNormalCreate body of documentationAaron Harper07/22/2013 11:34 pm
145 Groundstation v.2.0MilestoneNewNormalConnect Receiver and test satellite receptionAaron Harper07/02/2013 05:57 pm
144 Groundstation v.2.0MilestoneNewNormalComputer controlAaron Harper07/02/2013 05:56 pm
143 Groundstation v.2.0MilestoneNewNormalAssemble ground station Az-El mountAaron Harper07/02/2013 05:54 pm
142 Groundstation v.2.0MilestoneNewNormalOrder components and prepare preliminary assembliesAaron Harper07/24/2013 10:24 pm
141 Groundstation v.2.0MilestoneNewNormalGround Station DesignAaron Harper07/21/2013 10:51 pm
140 Groundstation v.2.0MilestoneNewNormalFeature requests and design requirements (SEP)Aaron Harper07/15/2013 02:28 pm

1 2 3 ... 6 Next » (1-25/133) | Per page: 25, 50, 100

Also available in: Atom CSV PDF