Operating Instructions

Version 6 (Skylar Hoffert, 09/20/2018 05:49 pm)

1 1 Skylar Hoffert
h1. Operating Instructions
2 1 Skylar Hoffert
3 1 Skylar Hoffert
{{>toc}}
4 1 Skylar Hoffert
5 1 Skylar Hoffert
h2. Preparing For A Pass
6 1 Skylar Hoffert
7 3 Skylar Hoffert
Run WXtoImg. Select *File* -> *Update Keplers*. This will update NOAA satellite TLEs so that your pass times are as up to date as possible.
8 1 Skylar Hoffert
9 3 Skylar Hoffert
In WXtoImg, select *File* -> *Satellite Pass List*. This window will display all future passes within a few days.
10 3 Skylar Hoffert
11 3 Skylar Hoffert
!preparing_for_a_pass_1.jpg!
12 3 Skylar Hoffert
13 3 Skylar Hoffert
Selecting an appropriate pass can be tricky. The most important characteristic for a good pass is the maximum elevation angle. Low maximum elevation angles will have short passes with insufficient gain to complete an image. High maximum elevation angles may have periods of insufficient gain when the satellite is directly overhead.
14 3 Skylar Hoffert
15 3 Skylar Hoffert
!preparing_for_a_pass_2.jpg!
16 3 Skylar Hoffert
17 4 Skylar Hoffert
*NOTE*: Frequencies in WXtoImg are *INCORRECT*. Use these frequencies for NOAA satellites:
18 3 Skylar Hoffert
19 4 Skylar Hoffert
* NOAA 15: 137.6200 MHz
20 4 Skylar Hoffert
* NOAA 18: 137.9125 MHz
21 4 Skylar Hoffert
* NOAA 19: 137.1000 MHz
22 4 Skylar Hoffert
23 4 Skylar Hoffert
*NOTE*: NOAA 17 is no longer in operation. Do not try to capture an image from NOAA 17.
24 3 Skylar Hoffert
25 1 Skylar Hoffert
h2. Placing The Antenna
26 1 Skylar Hoffert
27 3 Skylar Hoffert
Ensure that the antenna is perpendicular to the ground so that it is facing directly up (zenith). This will ensure gain is uniform across the radio horizon.
28 1 Skylar Hoffert
29 3 Skylar Hoffert
In some cases, when testing the antenna, the top of a vehicle was used. While having height off of the ground may be nice to reduce interference to the horizon, the vehicle may interfere and cause stray multi-path signals to affect the quality of the signal (negatively or positively). For more predictable behavior, place the antenna in the middle of a large field on a flat surface.
30 3 Skylar Hoffert
31 3 Skylar Hoffert
!placing_the_antenna_1.jpg!
32 3 Skylar Hoffert
33 3 Skylar Hoffert
h2. Receiving An Image
34 3 Skylar Hoffert
35 3 Skylar Hoffert
Once you have selected a sufficient pass, place the antenna and connect it to your computer with the *RTL-SDR Dongle*. Run SDR-Sharp and WXtoImg side by side so that you can watch both as the pass occurs.
36 3 Skylar Hoffert
37 5 Skylar Hoffert
Shortly before the pass begins, select *File* -> *Record* -> *Auto Record* in WXtoImg. WXtoImg will now wait for a pass to reach a sufficient elevation angle before starting to record.
38 5 Skylar Hoffert
39 6 Skylar Hoffert
While you wait for the recording to start, use SDR Sharp to locate the signal. It should appear with low intensity at first and increase over time. The image below is what the signal looks like near maximum.
40 6 Skylar Hoffert
41 6 Skylar Hoffert
!receiving_an_image_1.jpg!
42 3 Skylar Hoffert
43 1 Skylar Hoffert
h2. Troubleshooting
44 1 Skylar Hoffert
45 1 Skylar Hoffert
h3. WXtoImg shows a black screen with no image.
46 1 Skylar Hoffert
47 1 Skylar Hoffert
You must ensure VB Cable is transmitting sound to WXtoImg from SDR Sharp. Double check SDR Sharp audio output, ensure your microphone and speakers are not muted, turn up the volume for your VBCable in Audio Settings.
48 3 Skylar Hoffert
49 3 Skylar Hoffert
h3. I do not see a signal in SDR Sharp at the time of the pass.
50 3 Skylar Hoffert
51 3 Skylar Hoffert
There could be numerous things wrong with your setup. Ensure your ground station coordinates are correct on WXtoImg, double check that you are using the correct frequency (do NOT trust WXtoImg listed frequencies), and be sure that you are using local time and not UTC time.